Spray Type Cooling Tower (WYG-80T)
Enhanced Spray Distribution · Better Water-Air Contact · Higher Cooling Efficiency

The Challenge: Standard Water Distribution Wastes Fill Surface Area
In a standard cooling tower, water distribution is often uneven. Some areas of the fill receive more water than others. Uneven distribution means some fill surface is wasted. Uneven distribution means lower cooling efficiency. The Spray Type Cooling Tower (WYG-80T) uses enhanced spray technology. The spray system distributes water evenly across the entire fill surface. Every square centimeter of fill is used for cooling.
Real-World Case: Printing Facility in Zhejiang
A printing facility in Zhejiang installed a WYG-80T in October 2024. The facility operates high-speed printing presses that generate significant heat. The plant manager reported that the spray distribution system provides even water coverage. Cooling efficiency is 12% higher than their previous tower. The printing presses maintain consistent temperature, improving print quality.
"The spray system makes a noticeable difference. The water spreads evenly across the fill. We get better cooling with the same fan power."
- Mr. Ye, Printing Facility Manager

Core Performance Specifications
|
Parameter |
Value |
|
Cooling Water Flow Rate |
62.4 m³/h |
|
Inlet / Outlet Water Temperature |
37℃ / 32℃ |
|
Ambient Dry Bulb / Wet Bulb Temperature |
31.5℃ / 27℃ |
|
Cooling Capacity |
312,000 kcal/h |
|
Noise Level |
62.5 dB (A) |
|
Power Supply |
380V / 3P / 50Hz |
|
Drift Loss |
≤ 0.02% |
|
Evaporation Loss |
≤ 0.83% |
|
Inlet Water Pressure |
19 kPa |
|
Net Weight / Operating Weight |
400 kg / 1000 kg |
Why Does the WYG-80T Provide Better Cooling?
Enhanced Spray Distribution
The spray system uses specially designed nozzles. The nozzles create a uniform spray pattern. Water is distributed evenly across the entire fill surface. No area receives too much water. No area receives too little water. Every square centimeter of fill is used for heat transfer.
Optimized Nozzle Design
The nozzles are designed for the specific flow rate of the tower. They create droplets of the optimal size. Droplets that are too large do not have enough surface area for heat transfer. Droplets that are too small are carried away by the air stream. The nozzles in the WYG-80T are sized for the 62.4 m³/h flow rate.
Cross Flow Configuration
The tower uses cross flow configuration. Air moves horizontally across the falling water. The cross flow path provides excellent contact between air and water. The spray system enhances this contact by distributing water evenly.
Why This Matters for Your Operation
Better water distribution means better cooling efficiency. Better cooling efficiency means you get more cooling for the same fan power. More cooling per kilowatt means lower energy costs. The WYG-80T delivers 312,000 kcal/h of cooling capacity with efficient spray distribution.


Complete Technical Specification Table
|
Parameter |
Value |
|
Cooling Tower Type |
Counter Flow Round Water Tower |
|
Model |
WYG-80T |
|
Cooling Water Flow Rate |
62.4 m³/h |
|
Inlet / Outlet Water Temperature |
37℃ / 32℃ |
|
Ambient Dry Bulb / Wet Bulb Temperature |
31.5℃ / 27℃ |
|
Cooling Capacity |
312,000 kcal/h |
|
Noise Level |
62.5 dB (A) |
|
Power Supply |
380V / 3P / 50Hz |
|
Water Quality Requirement |
pH 6 – 8 |
|
Air-to-Water Ratio |
0.62 kg/kg |
|
Drift Loss |
≤ 0.02% |
|
Evaporation Loss |
≤ 0.83% |
|
Inlet Water Pressure |
19 kPa |
|
Net Weight / Operating Weight |
400 kg / 1000 kg |
|
Fan Type |
Axial Flow |
|
Air Volume |
34,320 m³/h |
|
Fan Diameter |
930 mm |
|
Number of Blades |
4 per set |
|
Drive Method |
Direct Drive |
|
Motor Power |
1.5 kW-8 |
|
Motor Start Method |
Direct Start |
|
Water Basin Diameter (D) |
2100 mm |
|
Tower Height (H) |
2750 mm |
|
Inlet / Outlet Pipe Size (DN) |
100 mm / 100 mm |
|
Overflow / Drain Pipe Diameter (DN) |
25 mm / 25 mm |
|
Automatic / Manual Make-up Size (DN) |
20 mm / None |
|
Fan Material |
Nylon |
|
Shell Material |
Molded FRP |
|
Center Pipe Material |
PVC |
|
Rotating Head Material |
Nylon |
|
Water Distribution Pipe Material |
PVC |
|
Fill Material |
PVC |
|
Float Valve Material |
Nylon |
|
Rope Joint Material |
Nylon |
|
Air Intake System Material |
PVC |
Hot Tags: spray type cooling tower, China spray type cooling tower manufacturers, suppliers, factory, Cross Flow Type Cooling Tower, Galvanized Steel Cooling Tower, High temperature Cooling Tower, Low Noise Cooling Tower, Vibration Damping Square Cooling Tower, Wet Cross Flow Cooling Tower

